Phone +49 7335 184 984 1Email vertrieb@krisch-dienst.de
Pressure test systems & high-pressure pumps up to 2660 bar · Water hydraulics: wasser-hydraulik.de
DeutschEnglishFrançaisEspañolNederlands
ElectronicsSafety & emergency stopHydraulic optionsTankFurther optionsPressure2excel™Accessories

Electronics & automation

…1EL…

Pressure sensor with digital display

Pressure sensor 0–10 V or 4–20 mA with digital display and 5 m connecting cable.

…2EL…

Electronic proportional pressure regulator

In addition to version 1EL, an electronic proportional pressure regulator with 5 m connecting cable for fully automatic pressure control.

SPS

Automatic test cycle

Test sequences controlled by PLC – also with operator panel, keypad and display.

KDDPA-2EL with proportional precision pressure control valve
KDDPA-2EL with proportional precision pressure control valve
PLC operator panel for automatic test cycles
PLC operator panel for automatic test cycles

Safety & emergency stop

KDD-PTJR-Not-Aus

Pneumatic emergency stop

The mushroom push-button vents the compressed air via a 1/2" 3/2-way valve – the pump stops immediately. The hydraulic pressure must be relieved separately. Reset by turning the mushroom push-button.

KDD-PTJR-Not-Aus-HYD-500 / -800

Emergency stop with hydraulic pressure relief

Requires KDD-PTJR-Not-Aus. The hydraulic pressure is fully relieved via a pneumatically actuated NO ball valve – up to 500 or 800 bar.

KDD-PTJR-EL-Not-Aus

Electrical emergency stop

In addition to the mushroom push-button, the compressed air can optionally be released via a 24 V solenoid valve 1/8" 3/2-way. The pump only runs when both the solenoid valve and the mushroom push-button are pressurised (AND logic).

KDD-PTJx-KH2-G1/2

Ball valve on water inlet

Stainless-steel ball valve with detachable union upstream of the pump – shuts off the water supply, e.g. after a test specimen has burst.

KDD-PTxx-2/2-G1/2-NC

Solenoid valve on water inlet

Like the ball valve upstream of the pump, as a 2/2-way solenoid valve NC. Also available purely pneumatic.

KDDPA03-PTMR755 with emergency stop
KDDPA03-PTMR755 with emergency stop
KDDPA-PTJR with hydraulic emergency stop
KDDPA-PTJR with hydraulic emergency stop

Hydraulic options

KDD-PTJX-2-Stufen

Two pressure stages

Pneumatic switching between two precision pressure regulators for repeatable pressure tests at two different pressures – additional precision pressure regulator with pressure gauge and 3-way ball valve, operated from above.

KDD-PTJx-BYPASS-665

Bypass for fast filling

Increases the flow rate during filling via an additional check valve: 18 l/min at 3 bar water pressure. Only in combination with the ball valve on the water inlet.

KDD-PTJx-204-226

Throttled pressure release

Throttle check valve and 2/2-way valve NC – for test specimens > 5 litres, up to 160 bar maximum pressure.

KDD-PTJx-KH2-G1/2HD

Ball valve on high-pressure side

Ball valve between pump and high-pressure block – the water pressure in the system can be held 100 %. Up to 500 bar.

KDD-PTxx-KH4/2-ZYL

4-way ball valve for cylinders

Actuating and locking a double-acting hydraulic cylinder. Negative overlap, locked position at 45° and 90° travel.

KDD-PTJx-M080-DIGI

Digital pressure gauge

Stainless-steel digital pressure gauge instead of the stainless-steel chemical pressure gauge.

KDDPA with two pressure stages
KDDPA with two pressure stages
KDDPA03-2EL-PTMR with bypass
KDDPA03-2EL-PTMR with bypass
KDDPA with 4-way ball valve and hydraulic cylinder
KDDPA with 4-way ball valve and hydraulic cylinder

Tank

KDD-PTJx-Tank-3L

Plastic tank 4 litres

Black plastic tank (3 l usable volume) with tank breather, suction line to the pump, built-in filling valve (float) and polyamide return piping with 3" mini filter.

KDD-PTJx-SS-Tank-3L

Stainless-steel tank for clean rooms

Stainless-steel tank without filling valve and return filter, with 10 µ stainless-steel suction filter upstream of the pump and stainless-steel tank breather.

KDDPA02 / 04

Large stainless-steel tank

Versions with a large tank (approx. 50 litres) for operation independent of the mains water supply.

KDD-DR-OB

Compressed-air ball valve on top

Ball valve for compressed air on top of the housing instead of front left.

KDDPA with small tank – top view
KDDPA with small tank – top view
KDDPA with small tank and sensor cable
KDDPA with small tank and sensor cable
KDDPA01-OIL for hydraulic oil
KDDPA01-OIL for hydraulic oil
KDDPA low pressure
KDDPA low pressure

Further options

  • Duo unit with two pumps and console housing
  • Automatic test cycle controlled by PLC
  • Large pump PTM with double displacement
  • Calibrated pressure sensors / gauges with 3.1 certificate
  • Pressure sensor in the water inlet
  • Hoses and test adapters
  • Bleed valve for test specimens
  • Pulsation damper
  • Castors with total lock on the housing
  • KDDPA-OIL – version for hydraulic oil
  • Filter silencer for even better noise reduction and oil separation
  • Clean-room version with oil-free pump, exhaust air collector and filter silencer

KDDPA Pressure2excel™

Data acquisition with set-point input – the test system is operated entirely from Excel.

Only in combination with KDDPA version 2EL with 0–10 V pressure sensor and proportional pressure valve. Adjustable parameters: repetition rate, set pressure, start / stop.

  • Plastic enclosure IP 56 (separate, not mounted in the KDDPA housing)
  • Plug-in power supply 24 V DC, 2.5 A, Schuko plug with 3 m cable
  • Data acquisition PLC with RBE-OS operating system
  • USB plug-and-play for programming and data acquisition – with app for data acquisition in Excel™
  • 5 m cable between control box and KDDPA system

Excel™ is a registered trademark of Microsoft.

Pressure2excel™ – scope of delivery
Pressure2excel™ – scope of delivery
KDDPA with Pressure2excel™ control
KDDPA with Pressure2excel™ control

Accessories

  • High-pressure hoses up to 210 bar, 800 bar and above 1000 bar
  • HYDOPLUG pipe plugs – inlet and outlet models with high-pressure bleed valve G1/4", up to 550 bar, for pipe inside diameters from 9.5 mm
  • Test adapters and bleed valves
  • Distribution blocks and multi-channel manifolds
Distribution block with bladder accumulator
Distribution block with bladder accumulator

Your pressure test – our test system

Tell us the test pressure, test medium and test specimen – we will configure the right KDDPA system or build your test bench to specification.

Send an enquiry